UWS Series
Sixteenth-brick DOSA-Compatible,
Wide Input Isolated DC-DC Converters
Performance Speci?cation Notes
1. All speci?cations are typical unless noted. Ambient temperature =
+25°Celsius, V IN is nominal, output current is maximum rated nominal.
External output capacitance is 1 μF multilayer ceramic paralleled with
10?μF electrolytic. All caps are low ESR. These capacitors are necessary for
our test equipment and may not be needed in your application.
Testing must be kept short enough that the converter does not appreciably
heat up during testing. For extended testing, use plenty of air?ow. See
Derating Curves for temperature performance. All models are stable and
regulate within spec without external cacacitance.
2. Input Ripple Current is tested and speci?ed over a 5-20 MHz bandwidth
and uses a special set of external ?lters only for the Ripple Current speci-
?cations. Input ?ltering is C IN = 33 μF, C BUS = 220 μF, L BUS = 12?μH. Use
capacitor rated voltages which are twice the maximum expected voltage.
Capacitors must accept high speed AC switching currents.
3. Note that Maximum Current Derating Curves indicate an average current
at nominal input voltage. At higher temperatures and/or lower air?ow, the
converter will tolerate brief full current outputs if the average RMS current
over time does not exceed the Derating curve. All Derating curves are
presented at sea level altitude. Be aware of reduced power dissipation
with increasing density altitude.
4. Mean Time Before Failure (MTBF) is calculated using the Telcordia
(Belcore) SR-332 Method 1, Case 3, Issue 1, ground ?xed conditions. Oper-
ating temperature = +30°C, full output load, natural air convection.
5. The output may be shorted to ground inde?nitely with no damage. The
Output Short Circuit Current shown in the speci?cations is an average con-
sisting of very short bursts of full rated current to test whether the output
circuit can be repowered.
6. The On/Off Control is normally driven from a switch or relay. An open
collector/open drain transistor may be used in saturation and cut-off
(pinch-off) modes. External logic may also be used if voltage levels are
fully compliant to the speci?cations.
7. Regulation speci?cations describe the deviation as the input line voltage
or output load current is varied from a nominal midpoint value to either
extreme (50% load).
8. Do not exceed maximum power ratings or output overvoltage when adjust-
ing output trim values.
9. At zero output current, Vout may contain components which slightly
exceed the ripple and noise speci?cations.
10. Output overload protection is non-latching. When the output overload
is removed, the output will automatically recover.
11. All models are fully operational and meet published speci?cations,
including “cold start” at –40°C.
12. The converter will shut off if the input falls below the undervoltage thresh-
old. It will not restart until the input exceeds the Input Start Up Voltage.
13. Short circuit shutdown begins when the output voltage degrades approxi-
mately 2% from the selected setting.
14. Output noise may be further reduced by installing an external ?lter. See
the Application Notes. Use only as much output ?ltering as needed and no
more . Larger caps (especially low-ESR ceramic types) may slow transient
response or degrade dynamic performance. Thoroughly test your applica-
tion with all components installed.
15. To avoid damage or unplanned shutdown, do not sink appreciable reverse
output current.
16. If reverse polarity is accidentally applied to the input, to ensure reverse
input protection with full output load, always connect an external fast blow
input fuse in series with the +V IN input.
17. Although extremely unlikely, failure of the internal components of this
product may expose external application circuits to dangerous voltages,
currents, temperatures or power levels. Please thoroughly verify all ap-
plications before committing them to service. Be sure to include appropri-
ately-rated FUSES (see speci?cations and Application Notes) to reduce the
risk of failure.
18. If remote sense is not used, connect it to its respective Vout terminal.
Sense is included on UWS-3.3/15-Q48 and UWS-5/10-Q48 models only.
19 Output Ripple and Noise for the UWS-5/10-Q48 model with a 1uF and
100uF Tantalum Output Capacitor is 65mVp-p (Typical).
www.murata-ps.com/support
MDC_UWS Series.C03 Page 14 of 25
相关PDF资料
UWS1V221MCL1GS CAP ALUM 220UF 35V 20% SMD
UWT1A102MNL1GS CAP ALUM 1000UF 10V 20% SMD
UWX1A151MCL1GB CAP ALUM 150UF 10V 20% SMD
UWZ1V331MCL1GS CAP ALUM 330UF 35V 20% SMD
UZD0J101MCL1GB CAP ALUM 100UF 6.3V 20% SMD
UZG1C470MCL1GB CAP ALUM 47UF 16V 20% SMD
UZP1V100MCL1GB CAP ALUM 10UF 35V 20% SMD
UZR1E330MCL1GB CAP ALUM 33UF 25V 20% SMD
相关代理商/技术参数
U-W-SCB-N-ADNET4-TIST-52-0-N 制造商:RoweBots Research Inc. 功能描述:DEVELOPMENT LICENSE UNISON V5 SOURCE CODE FOR TI ARM CM3/M4 - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET4-TIST-52-100-N 制造商:RoweBots Research Inc. 功能描述:DEVELOPMENT AND DEPLOYMENT 100K UNISON V5 SOURCE CODE FOR TI - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET4-TIST-52-10-N 制造商:RoweBots Research Inc. 功能描述:DEVELOPMENT AND DEPLOYMENT 10K UNISON V5 SOURCE CODE FOR TI - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET4-TIST-52-999-N 制造商:RoweBots Research Inc. 功能描述:DEVELOPMENT AND DEPLOYMENT >100K UNISON V5 SOURCE CODE FOR T - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET4-TIST-52-AR-N 制造商:RoweBots Research Inc. 功能描述:ROYALTY FREE ARCHITECTURE LICENSE UNISON V5 SOURCE CODE FOR - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET4-TIST-52-PF-N 制造商:RoweBots Research Inc. 功能描述:ROYALTY FREE PRODUCT FAMILY LICENSE UNISON V5 SOURCE CODE FO - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET4-TIST-52-PL-N 制造商:RoweBots Research Inc. 功能描述:ROYALTY FREE PRODUCT LINE LICENSE UNISON V5 SOURCE CODE FOR - Virtual or Non-Physical Inventory (Software & Literature)
U-W-SCB-N-ADNET6-TIST-52-0-N 制造商:RoweBots Research Inc. 功能描述:DEVELOPMENT LICENSE UNISON V5 SOURCE CODE FOR TI ARM CM3/M4 - Virtual or Non-Physical Inventory (Software & Literature)